Pistol Pricing

 Homepage Contact Work Order Labor Pricing charts



 

GENERAL PISTOL SERVICE

Complete clean, disassemble, safety check, oil and reassemble (rust

            Removal and or excessively dirty firearms are additional)               $60.00

Recrown for accuracy                                                                                               $60.00

Drill & Tap frame for scope mounts                                                              $140.00

Semi-auto pistol action job: clean & smooth action, not including

            any parts                                                                                         $140.00

Lower and flare ejection port (bluing additional)                                             $60.00

Polish barrel and feed ramp, starting at                                                          $80.00

Fit custom trigger, does not include cost of trigger                                       $60.00

Fit custom hammer, does not include cost of hammer                                $100.00

Mill slide for low profile rear sight                                                                 $160.00

Mill slide for front dovetail sight                                                                 $60.00

Install stake on front sight, does not include sight                                     $60.00

Install sights of any kind on most pistols, when milling is not

            required (sights additional)                                                                     Hourly rate

Install extended magazine release, does not include mag release              $40.00

Mill cocking serrations in the front of the slide, refinishing additional            $80.00

Stippling or texturing service available on most polymer frames              Quote

Tighten and lap slide and frame to a perfect "one to one" fit                          $140.00

Fit barrel

            Non-ramped barrel                                                                            $100.00

            Ramped barrel                                                                                     $180.00

Fit and install barrel bushing (does not include cost of bushing)                        $80.00

Bevel magazine well (bluing additional)                                                         $60.00

Checker front strap of 1911 style frame (available in 20,25 or 30 lines

            per inch)                                                                                         $240.00

Serrate rear of slide (less extractor) to 40 lines per inch

            (refinishing may be additional)                                                         $50.00

Lower and flare ejection port (bluing additional)                                             $60.00

Polish barrel and feed ramp, starting at                                                          $80.00

Fit custom trigger, does not include cost of trigger                                       $60.00

Fit custom hammer, does not include cost of hammer                                $100.00

Mill slide for low profile rear sight                                                                 $160.00

Mill slide for front dovetail sight                                                                 $60.00

Install stake on front sight, does not include sight                                     $60.00

Install extended magazine release, does not include mag release              $40.00

Modify frame for beavertail grip safety, does not include safety

            or refinishing                                                                                             $100.00

Mill cocking serrations in the front of the slide, refinishing additional            $80.00

Install extended ejector for increased reliability

            (rear of ejector is cold blued after fitting)                                       $60.00

Fit and install custom extended or ambidextrous safety lever, does not

            include safety lever                                                                               $40.00

Liquid conversion                                                                                            $300.00

1911 PERFORMANCE BUNDLES

The Dependable:

Completely disassemble, clean, check, and test fire, install Wolff

            custom recoil spring, firing pin, main and sear springs, tune the

            extractor, polish breech face, feed ramp and disconnector rail            $120.00

The Defense:

Completely disassemble, clean, check, and test fire, Install Novak fixed

            low mount rear sight and dovetail front sight, trigger job (4lbs),

            tune extractor, polish breech face, feed ramp and disconnector

            rail.                                                                                                       $200.00

The Tactical:

Completely dissemble, clean, check, and test fire.  Install Trijicon night

            sights, Wilson beavertail grip safety, cylinder & slide Tactical II

            trigger pull kit (includes 4lb pull, skeletonized tactical hammer

            with relieved sides to eliminate frame rub, ultra match sear and

            disconnector, light sear spring and 18lb hammer spring), Ed

            brown tactical safety, Wilson extended slide release, tune

            extractor polish breech face, feed ramp and disconnector rail.       $400.00

CUSTOM GLOCK SERVICE

Chamfer frame at mag catch gives better clearance                                              $40.00

Finger groove removal (left smooth)                                                                        $60.00

Finger groove removal (then 360 degree stipple)                                      $160.00

Grip reduction only (left smooth)                                                                        $160.00

360 degree stipple only                                                                                $120.00

Remove trigger guard hook and stipple                                                   $60.00

Beavertail added to frame                                                                          $200.00

Mill front cocking serrations (refinishing additional)                                              $80.00

Competition trigger job (reduces take up, over travel and reset)                 $90.00

Frame package (includes: Grip reduction, finger groove removal,

            chamfer frame at mag catch, 360 stipple)                                      $300.00